Sangong 952 Loader

  • Hydraulic Pump Regulator For Excavator Suppliers

    The various control of the hydraulic pump ultimately controls the swashplate angle by adjusting the servo piston to achieve the purpose of adjusting the flow of the hydraulic pump. Adjusting the pump flow rate is also adjusting the speed of the excavator. Reverse flow control. Reverse flow control.

    Learn More
  • Mini excavator hydraulic pump test - YouTube

    Jul 30, 2021 · The adjustment method of the maximum flow rate of the hydraulic pump: As shown in the figure, we need to loosen the regulator lock nut 1 and adjust the screw 2 at the same time. Remember that the direction of adjustment is clockwise to increase the …

    Learn More
  • Construction machinery_ Excavator hydraulic pump failure

    Sep 16, 2021 · Construction machinery_ Excavator hydraulic pump failure_ Typical fault analysis. ① Fault I. Fault phenomenon: the excavator rotates slowly and walks on the left, while the right walking and bucket movement speed are normal, the speed change of …

    Learn More
  • How to Better Handle the Excavator Hydraulic Pump After It

    The control valve and the full hydraulic steering gear are connected in series with a single pump, the safety valve is set to a pressure of 16 MPa, and the rated working pressure of the excavator hydraulic pump is also 16 MPa. Hydraulic pumps often work under full …

    Learn More
  • Kawasaki K3V/K5V displacement control transformation

    This post is about Kawasaki K3V/K5V series displacement controls - more precisely about how to transform a common negative displacement control (pilot pressure up - displacement down) into a positive displacement control (pilot pressure up - displacement up). Kawasaki K3V series is an old passion of mine. If I was asked to choose the best open circuit pump in the world - my subconscious …

    Learn More
  • Excavator uses 2-pump, negative flow hydraulic system.

    Mar 14, 2002 · The 325C L uses the proven open-center, two-pump, negative flow hydraulic system. Increased engine power allows increased hydraulic flow of 10 percent when compared to the previous model. Increased flow works with the hydraulic cross-sensing system to boost productivity through faster implement speeds and quicker, stronger pivot turns.

    Learn More
  • How to Better Handle the Excavator Hydraulic Pump After It

    The control valve and the full hydraulic steering gear are connected in series with a single pump, the safety valve is set to a pressure of 16 MPa, and the rated working pressure of the excavator hydraulic pump is also 16 MPa. Hydraulic pumps often work under full …

    Learn More
  • Komatsu excavator pilot pressure system and sensor

    Nov 15, 2018 · The temperature is: 120 °C. Maintenance of excavator table hydraulic excavator was successfully invented by the French Poclain factory. Due to the application of hydraulic technology, in the 1940s there was a suspended excavator equipped with a hydraulic backhoe on the tractor. 10.

    Learn More
  • US6202411B1 - Flow rate control device in a hydraulic

    When and How to Adjust a Load-sensing Hydraulic Pump

    Learn More
  • When and How to Adjust a Load-sensing Hydraulic Pump

    How it works: Hydraulic main pump K3V, K5V series Kawasaki

    Learn More
  • DEKA | Common maintenance problems about Kobelco excavator

    A: (1) the hydraulic pump and its control system are out of order, test the P1 and P2 pump pressure, the normal value should be 32-34M.(2) test the pressure of the pilot circuit, the pressure is always around 3.0M.(3) check whether the valve and the valve seat of the walking system are worn or not.(4) check the pressure of the running motor.

    Learn More
  • Hitachi ZX200-3 hydraulic pump hydraulic pump adjustment

    How it works: Hydraulic main pump K3V, K5V series Kawasaki

    Learn More
  • Adjust Hydraulic Pressure Relief Valve - Blogger

    Feb 05, 2015 · Recently purchased a used JCB 1CX. I attached a snowblower to the high flow circuit of the machine and it does not perform as one would expect. The blower calls for 55 lpm. From the specs I can locate it appears that the displacement rating for the …

    Learn More
  • What are the causes of hydraulic - China Mini Excavator

    In the hydraulic system of small excavator, because of the flow change of hydraulic oil, the internal pressure or partial pressure of the liquid will suddenly become low, resulting in the release of gas dissolved in the liquid and the generation of a large number of bubbles, which is …

    Learn More
  • Crawler Excavators - HydraForce

    This circuit provides responsive and smooth control of the fixed gear pump system for the breaker on a hydraulic excavator, using a solenoid valve, compensator, needle valve and relief valve. It has a maximum inlet flow of 180 lpm/47 gpm and a working pressure of 250 bar/3,625 psi. Quick Coupler Manifold.

    Learn More
  • Test & Adjust Doosan Ex | PDF | Engines | Pump

    1. Tools : 60 bar gauge, Tee type test adapter. 2. Test Condition : Over 50 ℃ of hydraulic oil temp. 3. Procedure. 1) Turn the engine speed to "Min" and check the pressure. 2) Turn the engine speed to "Max" and check the pressure. 3) If necessary, adjust the pilot …

    Learn More
  • How does the Carter excavator adjust the hydraulic pump

    First stage adjustment: First adjust the first stage of the constant power control of the right pump flow, loosen the lock nut 2, and turn the adjustment screw 1 to adjust the pump output flow. Clockwise adjustment increases pump output flow and counterclockwise adjustment reduces pump output flow.

    Learn More
  • Construction machinery_ Excavator hydraulic pump failure

    Sep 13, 2021 · The hydraulic pump used in the large excavator (dh220, 280 and other models) is K3V series swashplate axial piston pump. Its structure is a through shaft double piston pump, followed by an auxiliary pump to provide power for remote control. The main pump consists of a variable piston pump and a regulator that controls the displacement.

    Learn More
  • Yanmar 55 Excavator Hydraulic Pump

    Cautions of Hydraulic Pump Installation. 1.To replace a new hydraulic pump need to change new hydraulic oil and check whether the oil pipe is smooth to avoid the entry of impurities. If the impurities (iron scrap, copper scrap) are not cleaned up in oil pipes, but enter the new pump which will cause damage to the pump. 2.

    Learn More
  • Excavator Main Hydraulic Pump Receiving Pressure & …

    How it works: Hydraulic main pump K3V, K5V series Kawasaki

    Learn More